GT-S5690 1 country Android 2.3.6 (Gingerbread)

Samsung Galaxy cover S5690BOLL1 Firmware

Name: Samsung Galaxy cover (GT-S5690)
Brand: Samsung
Availability: InStock

Samsung Galaxy cover S5690BOLL1 is an Android 2.3.6 (Gingerbread) firmware for Germany (DTM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. A newer build for GT-S5690 is available: S5690XXNE1 https://samfirm.shop/build/S5690XXNE1.

8.7/10 (488)4,377 times

Android 2.3.6 (Gingerbread)

OS Version

2012-12-14

Build Date

n/a

Security patch

Countries

CSC codes

B (11)

Bootloader binary

Bootloader binary B (11). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy cover use bootloader binary X (33) (latest: S5690XXNE1). If your device already runs binary X (33), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: S5690XXLL1

Model	Region	CSC Version	Release date	Size	File name	Download
GT-S5690	DTM Germany	S5690DTMLK1	2013-01-16	143.657 MiB	GT-S5690_DTM_1_20130604210633_n3ja5nw8cr_fac.zip

Device specifications

Launched withAndroid 2.3
Display diagonal9.27 cm (3.65")
Display resolution320 x 480 pixels
Display typeTFT
Processor frequency0.8 GHz
Rear camera resolution3.2 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity1500 mAh
Weight100 g

How to flash S5690BOLL1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

S5690BOLL1 has bootloader binary B (11). Your device must run binary B (11) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

S5690BOLL1 is Android 2.3.6 (Gingerbread) firmware for Samsung Galaxy cover, released for Germany (DTM). Samsung built it on 2012-12-14.

No. A newer build for GT-S5690 is available: S5690XXNE1. Install it instead of S5690BOLL1 unless you need this exact version.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 143.657 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy cover must be on bootloader binary B (11) or lower.

This build uses bootloader binary B (11). It can be flashed on a Samsung Galaxy cover running binary B (11) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.