Samsung Galaxy Xcover2 S7710LUBAMC1
GT-S7710L 3 countries Android 4.1.2 (Jelly Bean)

Samsung Galaxy Xcover2 S7710LUBAMC1 Firmware

Samsung Galaxy Xcover2 S7710LUBAMC1 is an Android 4.1.2 (Jelly Bean) firmware for Chile (CHO), Panama (TPA), Trinidad & Tobago (TTT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. A newer build for GT-S7710L is available: S7710LUBAND2.

9.2/10 (471)13,095 times
Android 4.1.2 (Jelly Bean)
OS Version
2013-03-05
Build Date
n/a
Security patch
3
Countries
3
CSC codes
B (11)
Bootloader binary

Bootloader binary B (11). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: S7710LUBAMC1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    GT-S7710L
    CHO Chile
    		S7710LUUBAMC1 — 715.808 MiB
    GT-S7710L_1_20150923161740_1jfzixarcv_fac.zip
    GT-S7710L
    TPA Panama
    		S7710LUUBAMC1 2013-05-15 — —
    GT-S7710L
    TTT Trinidad & Tobago
    		S7710LUUBAMC1 2013-05-15 — —

    No matching downloads

    How to flash S7710LUBAMC1

    • S7710LUBAMC1 has bootloader binary B (11). Your device must run binary B (11) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    S7710LUBAMC1 is Android 4.1.2 (Jelly Bean) firmware for Samsung Galaxy Xcover2, released for Chile (CHO), Panama (TPA), Trinidad & Tobago (TTT). Samsung built it on 2013-03-05.

    No. A newer build for GT-S7710L is available: S7710LUBAND2. Install it instead of S7710LUBAMC1 unless you need this exact version.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 715.808 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Xcover2 must be on bootloader binary B (11) or lower.

    This build uses bootloader binary B (11). It can be flashed on a Samsung Galaxy Xcover2 running binary B (11) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Xcover2

    No changelog details available.
    No changelog details available.
    No changelog details available.
    Model firmware by region