Samsung Galaxy Note 2 (Docomo) SC02EOMUBNJ2
SC-02E 1 country Android 4.3 (Jelly)

Samsung Galaxy Note 2 (Docomo) SC02EOMUBNJ2 Firmware

Samsung Galaxy Note 2 (Docomo) SC02EOMUBNJ2 is an Android 4.3 (Jelly) firmware for Japan (DCM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build SC02EOMAMB1: Android updated from Jelly(Android Bean) to Android 4.3 (Jelly); bootloader binary raised from M (22) to U (30), so after installing it there is no way back to older builds. A newer build for SC-02E is available: SC02EOMUBRG2.

9.4/10 (453)8,718 times
Android 4.3 (Jelly)
OS Version
2014-10-10
Build Date
n/a
Security patch
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: SC02EOMUBNJ2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SC-02E
    DCM Japan
    		SC02EBNJ2 — — —
    SC-02E
    DCM Japan
    		SC02EDCMBNJ2 2014-10-20 1.28 GiB
    SC-02E_1_20180730145639_6lf8tv0tpc_fac.zip

    No matching downloads

    How to flash SC02EOMUBNJ2

    • SC02EOMUBNJ2 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    SC02EOMUBNJ2 is Android 4.3 (Jelly) firmware for Samsung Galaxy Note 2 (Docomo), released for Japan (DCM). Samsung built it on 2014-10-10.

    No. A newer build for SC-02E is available: SC02EOMUBRG2. Install it instead of SC02EOMUBNJ2 unless you need this exact version. The previous build was SC02EOMAMB1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.28 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Note 2 (Docomo) must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Note 2 (Docomo) running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Note 2 (Docomo)

    No changelog details available.
    No changelog details available.
    No changelog details available.
    No changelog details available.
    Model firmware by region