Samsung GALAXY S III alpha SC03EOMUBNL1
SC-03E 1 country Android 4.3 (Jelly)

Samsung GALAXY S III alpha SC03EOMUBNL1 Firmware

Samsung GALAXY S III alpha SC03EOMUBNL1 is an Android 4.3 (Jelly) firmware for Japan (DCM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build SC03EOMUBNK2: Android updated from Jelly(Android Bean) to Android 4.3 (Jelly). A newer build for SC-03E is available: SC03EOMUBOG5.

9.2/10 (453)8,459 times
Android 4.3 (Jelly)
OS Version
2014-12-22
Build Date
n/a
Security patch
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: SC03EOMUBNL1
    ModelRegionCSC VersionSizeFile nameDownload
    SC-03E
    DCM Japan
    		SC03EBNL1 — —
    SC-03E
    DCM Japan
    		SC03EDCMBNL1 1.055 GiB
    SC-03E_1_20170124182813_0bozlinl21_fac.zip

    No matching downloads

    How to flash SC03EOMUBNL1

    • SC03EOMUBNL1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    SC03EOMUBNL1 is Android 4.3 (Jelly) firmware for Samsung GALAXY S III alpha, released for Japan (DCM). Samsung built it on 2014-12-22.

    No. A newer build for SC-03E is available: SC03EOMUBOG5. Install it instead of SC03EOMUBNL1 unless you need this exact version. The previous build was SC03EOMUBNK2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.055 GiB; keep about twice that free on the computer to unzip it. The Samsung GALAXY S III alpha must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung GALAXY S III alpha running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung GALAXY S III alpha

    No changelog details available.
    No changelog details available.
    No changelog details available.
    No changelog details available.
    Model firmware by region