SM-T560 1 country Android 4.4.4 (KitKat)

Samsung Galaxy Tab E T560XXU0AOK2 Firmware

Name: Samsung Galaxy Tab E (SM-T560)
Brand: Samsung
Availability: InStock

Samsung Galaxy Tab E T560XXU0AOK2 is an Android 4.4.4 (KitKat) firmware for New Zealand (XNZ). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T560XXU0AOK1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-T560 is available: T560XXU0ARK2.

9.0/10 (470)8,742 times

Android 4.4.4 (KitKat)

OS Version

2015-11-13

First release

other regions until 2015-12-03

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: T560XXU0AOK2

Model	Region	CSC Version	Build Date	Release date	Size	File name	Download
SM-T560	XNZ New Zealand	T560XNZ0AOK2	2015-12-03	2015-12-03	632.894 MiB	SM-T560_1_20151203132753_rrwm194gyb_fac.zip
SM-T560	XNZ New Zealand	T5600AOK2	2015-11-13	—	—	—

Device specifications

Display diagonal24.4 cm (9.6")
Display resolution1280 x 800 pixels
Processor frequency1.3 GHz
Rear camera resolution5 MP
Rear camera typeSingle camera
Front camera resolution2 MP
Wi-Fi standardWi-Fi 4 (802.11n)
Weight490 g

How to flash T560XXU0AOK2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

T560XXU0AOK2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

T560XXU0AOK2 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy Tab E, released for New Zealand (XNZ). Samsung built it on 2015-11-13.

No. A newer build for SM-T560 is available: T560XXU0ARK2. Install it instead of T560XXU0AOK2 unless you need this exact version. The previous build was T560XXU0AOK1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 632.894 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab E must be on bootloader binary 0 or lower.

This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Tab E running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 38 other builds of this model use the same binary, so you can switch between them in both directions.