Samsung GALAXY S Ⅲ T999NUVUBOH1
SGH-T999N 1 country Android 4.3 (Jelly)

Samsung GALAXY S Ⅲ T999NUVUBOH1 Firmware

Samsung GALAXY S Ⅲ T999NUVUBOH1 is an Android 4.3 (Jelly) firmware for United States (TMB). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build T999NUVUBNC1: Android updated from Jelly(Android Bean) to Android 4.3 (Jelly). A newer build for SGH-T999N is available: T999NUVAME4.

8.9/10 (452)8,592 times
Android 4.3 (Jelly)
OS Version
2015-08-13
Build Date
n/a
Security patch
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung GALAXY S Ⅲ use bootloader binary V (31) (latest: T999NUVAME4). If your device already runs binary V (31), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: T999NUVUBOH1
    ModelRegionCSC VersionBuild DateSizeFile nameDownload
    SGH-T999N
    TMB United States
    		T999NBOH1 2015-08-13 — —
    SGH-T999N
    TMB United States
    		T999NTMBBOH1 — — —

    No matching downloads

    How to flash T999NUVUBOH1

    • T999NUVUBOH1 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    T999NUVUBOH1 is Android 4.3 (Jelly) firmware for Samsung GALAXY S Ⅲ, released for United States (TMB). Samsung built it on 2015-08-13.

    No. A newer build for SGH-T999N is available: T999NUVAME4. Install it instead of T999NUVUBOH1 unless you need this exact version. The previous build was T999NUVUBNC1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung GALAXY S Ⅲ must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung GALAXY S Ⅲ running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung GALAXY S Ⅲ

    No changelog details available.
    No changelog details available.
    No changelog details available.
    No changelog details available.
    Model firmware by region