Samsung Galaxy Tab S8+ 5G X806NKOU3CVL2
SM-X806N 1 country Android 13

Samsung Galaxy Tab S8+ 5G X806NKOU3CVL2 Firmware

Samsung Galaxy Tab S8+ 5G X806NKOU3CVL2 is an Android 13 firmware for South Korea (KOO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build X806NKOU2CVK5: bootloader binary raised from 2 to 3, so after installing it there is no way back to older builds. A newer build for SM-X806N is available: X806NKOSBJZH3.

OS updates guaranteed until: Android 16Security updates until: Feb 26, 2027
8.9/10 (455)4,425 times
Android 13
OS Version
2022-12-21
Build Date
n/a
Security patch
1
Countries
1
CSC codes
3
Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Tab S8+ 5G use bootloader binary B (11) (latest: X806NKOSBJZH3). If your device already runs binary B (11), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: X806NKOU3CVL2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-X806N
    KOO South Korea
    		X806NKOO3CVL2 2022-12-21 6.836 GiB
    SM-X806N_2_20221209110540_idkw6u04vv_fac.zip

    No matching downloads

    How to flash X806NKOU3CVL2

    • X806NKOU3CVL2 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal31.5 cm (12.4")
    • Display resolution2800 x 1752 pixels
    • Display technologyOLED
    • Rear camera resolution13 MP
    • Front camera resolution12 MP
    • Wi-Fi standardWi-Fi 6 (802.11ax)
    • Weight572 g

    Specifications of SM-X806B, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    X806NKOU3CVL2 is Android 13 firmware for Samsung Galaxy Tab S8+ 5G, released for South Korea (KOO). Samsung built it on 2022-12-21.

    No. A newer build for SM-X806N is available: X806NKOSBJZH3. Install it instead of X806NKOU3CVL2 unless you need this exact version. The previous build was X806NKOU2CVK5.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 6.836 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Tab S8+ 5G must be on bootloader binary 3 or lower.

    This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy Tab S8+ 5G running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Tab S8+ 5G

    No changelog details available.
    Model firmware by region