Samsung Galaxy A3 A300FXXS1BPK3 Firmware
Samsung Galaxy A3 A300FXXS1BPK3 is an Android 5.0.2 (Lollipop) firmware for 5 countries, 5 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build A300FXXU1BPJ2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-A300F is available: A300FXXS1BRI1.
9.3/10 (36)21,878 times
Android 5.0.2 (Lollipop)
OS Version
2016-11-28
First release
other regions until 2017-01-27
n/a
Security patch
5
Countries
5
CSC codes
1
Bootloader binary
Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
No matching downloads
Device specifications
- Launched withAndroid 4.4
- Display diagonal11.4 cm (4.5")
- Display resolution540 x 960 pixels
- Display typeSAMOLED
- Processor frequency1.2 GHz
- RAM1 GB
- Rear camera resolution8 MP
- Rear camera typeSingle camera
- SIM cardsDual SIM
- Battery capacity1900 mAh
- Weight110 g
How to flash A300FXXS1BPK3
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- A300FXXS1BPK3 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
A300FXXS1BPK3 is Android 5.0.2 (Lollipop) firmware for Samsung Galaxy A3, released for 5 countries, 5 CSC codes. Samsung built it on 2016-11-28.
No. A newer build for SM-A300F is available: A300FXXS1BRI1. Install it instead of A300FXXS1BPK3 unless you need this exact version. The previous build was A300FXXU1BPJ2.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy A3 must be on bootloader binary 1 or lower.
This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy A3 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 64 other builds of this model use the same binary, so you can switch between them in both directions.
Other builds and changelog for Samsung Galaxy A3
Show 15 older builds
No changelog details available.