Samsung Galaxy Jump A326KKSU3BVG2
SM-A326K 1 country Android 12

Samsung Galaxy Jump A326KKSU3BVG2 Firmware

Samsung Galaxy Jump A326KKSU3BVG2 is an Android 12 firmware for South Korea (KTC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build A326KKSU3BVF1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-A326K is available: A326KKSS8DYB1.

OS updates guaranteed until: Android 13Security updates until: Mar 3, 2025
Download firmware
9.3/10 (493)4,353 times
Android 12
OS Version
2022-08-04
Build Date
1
Countries
1
CSC codes
3
Bootloader binary

Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Jump use bootloader binary 8 (latest: A326KKSS8DYB1). If your device already runs binary 8, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: A326KKSU3BVG2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-A326K
    KTC South Korea
    		A326KKTC3BVG2 2022-08-04 5.15 GiB
    SM-A326K_2_20220725082140_h1864fzmwv_fac.zip
    		Download

    No matching downloads

    How to flash A326KKSU3BVG2

    • A326KKSU3BVG2 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal16.5 cm (6.5")
    • Display resolution720 x 1600 pixels
    • Display typeTFT
    • RAM4 GB
    • Rear camera resolution48 MP
    • Rear camera typeQuad camera
    • Battery capacity5000 mAh
    • Weight205 g

    Specifications of SM-A326B, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    A326KKSU3BVG2 is Android 12 firmware for Samsung Galaxy Jump, released for South Korea (KTC). Samsung built it on 2022-08-04.

    No. A newer build for SM-A326K is available: A326KKSS8DYB1. Install it instead of A326KKSU3BVG2 unless you need this exact version. The previous build was A326KKSU3BVF1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 5.15 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Jump must be on bootloader binary 3 or lower.

    This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy Jump running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 11 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Jump

    No changelog details available.
    Model firmware by region