SM-A600AZ 1 country Android 10

Samsung Galaxy A6 A600AZTUSACUC2 Firmware

Samsung Galaxy A6 A600AZTUSACUC2 is an Android 10 firmware for United States (AIO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build A600AZTUSACTL1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-A600AZ is available: A600AZTUSDCVC1.

Download firmware
8.7/10 (36)100 times
Android 10
OS Version
2021-03-23
Build Date
1
Countries
1
CSC codes
A (10)
Bootloader binary

Bootloader binary A (10). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy A6 use bootloader binary D (13) (latest: A600AZTUSDCVC1). If your device already runs binary D (13), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: A600AZTUSACUC2
    ModelRegionCSC VersionSizeFile nameDownload
    SM-A600AZ
    AIO United States
    		A600AZAIOACUC2 2.916 GiB
    SM-A600AZ_2_20210323135906_uihvpp3djp_fac.zip
    		Download

    No matching downloads

    How to flash A600AZTUSACUC2

    • A600AZTUSACUC2 has bootloader binary A (10). Your device must run binary A (10) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 8.0
    • Display diagonal14.2 cm (5.6")
    • Display resolution720 x 1480 pixels
    • Display typeSAMOLED
    • RAM3 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • Battery capacity3000 mAh

    Specifications of SM-A600F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    A600AZTUSACUC2 is Android 10 firmware for Samsung Galaxy A6, released for United States (AIO). Samsung built it on 2021-03-23.

    No. A newer build for SM-A600AZ is available: A600AZTUSDCVC1. Install it instead of A600AZTUSACUC2 unless you need this exact version. The previous build was A600AZTUSACTL1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.916 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy A6 must be on bootloader binary A (10) or lower.

    This build uses bootloader binary A (10). It can be flashed on a Samsung Galaxy A6 running binary A (10) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy A6

    No changelog details available.
    Model firmware by region