Samsung Galaxy A6+ A605FNXXU5CTE1 Firmware
Samsung Galaxy A6+ A605FNXXU5CTE1 is an Android 10 firmware for 5 countries, 5 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build A605FNXXU5CTD1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-A605FN is available: A605FNXXU8CVF1.
8.7/10 (25)21,682 times
Android 10
OS Version
2020-05-21
First release
other regions until 2020-05-29
2020-03-01
Security patch
5
Countries
5
CSC codes
5
Bootloader binary
Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy A6+ use bootloader binary 8 (latest: A605FNXXU8CVF1). If your device already runs binary 8, this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
No matching downloads
Device specifications
- Launched withAndroid 8.0
- Display diagonal15.2 cm (6")
- Display resolution1080 x 2220 pixels
- Display typeSAMOLED
- Processor frequency1.8 GHz
- Processor familyQualcomm Snapdragon
- Processor model450
- RAM3 GB
- Rear camera resolution16 MP
- Rear camera typeDual camera
- SIM cardsDual SIM
- Battery capacity3500 mAh
- Weight191 g
What's new in A605FNXXU5CTE1
· Security patch update
How to flash A605FNXXU5CTE1
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- A605FNXXU5CTE1 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
A605FNXXU5CTE1 is Android 10 firmware for Samsung Galaxy A6+, released for 5 countries, 5 CSC codes. It includes the 2020-03-01 security patch. Samsung built it on 2020-05-21.
No. A newer build for SM-A605FN is available: A605FNXXU8CVF1. Install it instead of A605FNXXU5CTE1 unless you need this exact version. The previous build was A605FNXXU5CTD1.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy A6+ must be on bootloader binary 5 or lower.
This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy A6+ running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 17 other builds of this model use the same binary, so you can switch between them in both directions.