Samsung GT-B9150 B9150XXUBMI2
GT-B9150 3 countries Android 4.2.2 (Jelly Bean)

Samsung GT-B9150 B9150XXUBMI2 Firmware

Samsung GT-B9150 B9150XXUBMI2 is an Android 4.2.2 (Jelly Bean) firmware for Czechia (ETL), Russia (SER), Ukraine (SEK). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build B9150XXUBMI1: Android updated from Jelly(Android Bean) to Android 4.2.2 (Jelly Bean). A newer build for GT-B9150 is available: B9150UEUBNF1.

Download firmware
8.8/10 (475)12,860 times
Android 4.2.2 (Jelly Bean)
OS Version
2013-09-16
Build Date
3
Countries
3
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: B9150XXUBMI2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    GT-B9150
    ETL Czechia
    		B9150OXXBMI3 — 1.119 GiB
    GT-B9150_ETL_1_20140723153600_3bak9kh5q0_fac.zip
    GT-B9150
    SEK Ukraine
    		B9150OXEBMH3 — 1.09 GiB
    GT-B9150_1_20151015213726_in6v844m2c_fac.zip
    GT-B9150
    SER Russia
    		B9150OXEBMH3 2013-10-10 1.11 GiB
    GT-B9150_SER_1_20150202133950_9cdc00vywg_fac.zip

    No matching downloads

    How to flash B9150XXUBMI2

    • B9150XXUBMI2 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of B9150XXUBMI2 by region

    Samsung released this build in all regions (1) on the same day, October 10, 2013.

    Frequently Asked Questions

    B9150XXUBMI2 is Android 4.2.2 (Jelly Bean) firmware for Samsung GT-B9150, released for Czechia (ETL), Russia (SER), Ukraine (SEK). Samsung built it on 2013-09-16.

    No. A newer build for GT-B9150 is available: B9150UEUBNF1. Install it instead of B9150XXUBMI2 unless you need this exact version. The previous build was B9150XXUBMI1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung GT-B9150 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung GT-B9150 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 7 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung GT-B9150

    No changelog details available.
    Model firmware by region