SHV-E330S 1 country Android 5.0.1 (KitKat)

Samsung Galaxy S4 LTE-A (Korea) E330SKSUDOC2 Firmware

Name: Samsung Galaxy S4 LTE-A (Korea) (SHV-E330S)
Brand: Samsung
Availability: InStock

Samsung Galaxy S4 LTE-A (Korea) E330SKSUDOC2 is an Android 5.0.1 (KitKat) firmware for South Korea (SKT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build E330SKSUCNJ1 https://samfirm.shop/build/E330SKSUCNJ1: Android updated from Android 4.4.2 (KitKat) to Android 5.0.1 (KitKat). A newer build for SHV-E330S is available: E330SKSUDPI2 https://samfirm.shop/build/E330SKSUDPI2.

8.9/10 (497)8,901 times

Android 5.0.1 (KitKat)

OS Version

2015-03-02

Build Date

n/a

Security patch

Countries

CSC codes

U (30)

Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: E330SKSUDOC2

Model	Region	CSC Version	Size	File name	Download
SHV-E330S	SKT South Korea	E330SDOC2	—	—
SHV-E330S	SKT South Korea	E330SYKTDOC2	—	—

How to flash E330SKSUDOC2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

E330SKSUDOC2 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

E330SKSUDOC2 is Android 5.0.1 (KitKat) firmware for Samsung Galaxy S4 LTE-A (Korea), released for South Korea (SKT). Samsung built it on 2015-03-02.

No. A newer build for SHV-E330S is available: E330SKSUDPI2. Install it instead of E330SKSUDOC2 unless you need this exact version. The previous build was E330SKSUCNJ1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S4 LTE-A (Korea) must be on bootloader binary U (30) or lower.

This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S4 LTE-A (Korea) running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.