Samsung Galaxy S4 LTE-A (Korea) E330SKSUDOL4
SHV-E330S 1 country Android 5.0.1 (KitKat)

Samsung Galaxy S4 LTE-A (Korea) E330SKSUDOL4 Firmware

Samsung Galaxy S4 LTE-A (Korea) E330SKSUDOL4 is an Android 5.0.1 (KitKat) firmware for South Korea (SKT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build E330SKSUDOH2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SHV-E330S is available: E330SKSUDPI2.

Download firmware
8.9/10 (37)9,084 times
Android 5.0.1 (KitKat)
OS Version
2015-12-24
First release
other regions until 2016-01-11
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SHV-E330S
    SKT South Korea
    		E330SSKTDOL4E330SKSUDOK1 2016-01-11 2016-01-11 1.672 GiB
    SHV-E330S_3_20160111171601_9d8xdiw34z_fac.zip
    SHV-E330S
    SKT South Korea
    		E330SDOL4E330SKSUDOL4 2015-12-24 — — —
    SHV-E330S
    SKT South Korea
    		E330SYKTDOL4E330SKSUDOK1 2015-12-24 2016-01-11 1.66 GiB
    SHV-E330S_10_20161006194341_q4wsrum2wl_fac.zip

    No matching downloads

    How to flash E330SKSUDOL4

    • E330SKSUDOL4 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    E330SKSUDOL4 is Android 5.0.1 (KitKat) firmware for Samsung Galaxy S4 LTE-A (Korea), released for South Korea (SKT). Samsung built it on 2015-12-24.

    No. A newer build for SHV-E330S is available: E330SKSUDPI2. Install it instead of E330SKSUDOL4 unless you need this exact version. The previous build was E330SKSUDOH2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S4 LTE-A (Korea) must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy S4 LTE-A (Korea) running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 9 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S4 LTE-A (Korea)

    No changelog details available.
    Model firmware by region