Samsung Galaxy E7 E7000ZSU1AOF1
SM-E7000 2 countries Android 4.4.4 (KitKat)

Samsung Galaxy E7 E7000ZSU1AOF1 Firmware

Samsung Galaxy E7 E7000ZSU1AOF1 is an Android 4.4.4 (KitKat) firmware for Hong Kong SAR China (TGY), Taiwan (BRI). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build E7000ZCU1AOE2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-E7000 is available: E7000ZCU1AQA2.

Download firmware
9.1/10 (465)8,729 times
Android 4.4.4 (KitKat)
OS Version
2015-06-01
Build Date
2
Countries
2
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: E7000ZSU1AOF1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-E7000
    BRI Taiwan
    		E7000OZS1AOF1 2015-06-19 1.107 GiB
    SM-E7000_1_20170320193413_9wkmlqt8zm_fac.zip
    		Download
    SM-E7000
    TGY Hong Kong SAR China
    		E7000OZS1AOF1 — 1.105 GiB
    SM-E7000_1_20151125191527_z9mo75xnyd_fac.zip
    		Download

    No matching downloads

    How to flash E7000ZSU1AOF1

    • E7000ZSU1AOF1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of E7000ZSU1AOF1 by region

    Samsung released this build in all regions (1) on the same day, June 19, 2015.

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1280 x 720 pixels
    • Display typeSAMOLED
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity2950 mAh
    • Weight141 g

    Specifications of SM-E700H, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    E7000ZSU1AOF1 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy E7, released for Hong Kong SAR China (TGY), Taiwan (BRI). Samsung built it on 2015-06-01.

    No. A newer build for SM-E7000 is available: E7000ZCU1AQA2. Install it instead of E7000ZSU1AOF1 unless you need this exact version. The previous build was E7000ZCU1AOE2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy E7 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy E7 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 15 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy E7

    No changelog details available.
    Model firmware by region