Samsung Galaxy E7 E7009KES1APK1
SM-E7009 1 country Android 4.4.4 (KitKat)

Samsung Galaxy E7 E7009KES1APK1 Firmware

Samsung Galaxy E7 E7009KES1APK1 is an Android 4.4.4 (KitKat) firmware for China (CTC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build E7009KEU1AOI2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-E7009 is available: E7009KES1AQA2.

Download firmware
8.9/10 (460)8,493 times
Android 4.4.4 (KitKat)
OS Version
2016-11-28
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionRelease dateSizeFile nameDownload
    SM-E7009
    CTC China
    		E70091APK1E7009KES1APK1 — — — Download
    SM-E7009
    CTC China
    		E7009CTC1APK1E7009KEU1AOE3 2016-12-21 1.099 GiB
    SM-E7009_1_20170124121939_drh7smsj26_fac.zip
    		Download

    No matching downloads

    How to flash E7009KES1APK1

    • E7009KES1APK1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1280 x 720 pixels
    • Display typeSAMOLED
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity2950 mAh
    • Weight141 g

    Specifications of SM-E700H, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    E7009KES1APK1 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy E7, released for China (CTC). Samsung built it on 2016-11-28.

    No. A newer build for SM-E7009 is available: E7009KES1AQA2. Install it instead of E7009KES1APK1 unless you need this exact version. The previous build was E7009KEU1AOI2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.099 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy E7 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy E7 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 8 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy E7

    No changelog details available.
    Model firmware by region