Samsung Galaxy Z Flip F700NTBU1BTH2
SM-F700N 1 country Android 10

Samsung Galaxy Z Flip F700NTBU1BTH2 Firmware

Samsung Galaxy Z Flip F700NTBU1BTH2 is an Android 10 firmware for South Korea (KOO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build F700NKOU1ATF4, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-F700N is available: F700NKOS4KWL1.

Download firmware
9.3/10 (483)4,282 times
Android 10
OS Version
2020-08-11
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Z Flip use bootloader binary 4 (latest: F700NKOS4KWL1). If your device already runs binary 4, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: F700NKRU1BTH2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-F700N
    KOO South Korea
    		F700NOKT1BTH2 2020-08-24 5.338 GiB
    SM-F700N_10_20211001233836_g00u3fsu49_fac.zip
    		Download

    No matching downloads

    How to flash F700NTBU1BTH2

    • F700NTBU1BTH2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 10.0
    • Display diagonal17 cm (6.7")
    • Display resolution2636 x 1080 pixels
    • Display typeDynamic AMOLED
    • RAM8 GB
    • Rear camera resolution12 MP
    • Rear camera typeDual camera
    • Battery capacity3300 mAh
    • Weight183 g

    Specifications of SM-F700F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    F700NTBU1BTH2 is Android 10 firmware for Samsung Galaxy Z Flip, released for South Korea (KOO). Samsung built it on 2020-08-11.

    No. A newer build for SM-F700N is available: F700NKOS4KWL1. Install it instead of F700NTBU1BTH2 unless you need this exact version. The previous build was F700NKOU1ATF4.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 5.338 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Z Flip must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Z Flip running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 19 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Z Flip

    No changelog details available.
    Model firmware by region