Samsung Galaxy Pocket2 G110MUBU0APB1
SM-G110M 1 country Android 4.4.2 (KitKat)

Samsung Galaxy Pocket2 G110MUBU0APB1 Firmware

Samsung Galaxy Pocket2 G110MUBU0APB1 is an Android 4.4.2 (KitKat) firmware for Uruguay (UPO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G110MUBU0AOG1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G110M is available: G110MUBS0AQA4.

Download firmware
8.9/10 (477)4,366 times
Android 4.4.2 (KitKat)
OS Version
2016-02-23
Build Date
1
Countries
1
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G110MUBU0AOI2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G110M
    UPO Uruguay
    		G110MUUB0APB1 2016-03-23 532.267 MiB
    SM-G110M_1_20170201091439_y5b6d82qe7_fac.zip
    		Download

    No matching downloads

    How to flash G110MUBU0APB1

    • G110MUBU0APB1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal8.38 cm (3.3")
    • Display resolution240 x 320 pixels
    • Display typeTFT
    • RAM0.5 GB
    • Rear camera resolution2 MP
    • Rear camera typeSingle camera
    • Battery capacity1200 mAh
    • Weight107 g

    Specifications of SM-G110H, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G110MUBU0APB1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Pocket2, released for Uruguay (UPO). Samsung built it on 2016-02-23.

    No. A newer build for SM-G110M is available: G110MUBS0AQA4. Install it instead of G110MUBU0APB1 unless you need this exact version. The previous build was G110MUBU0AOG1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 532.267 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Pocket2 must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Pocket2 running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 11 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Pocket2

    No changelog details available.
    Model firmware by region