SM-G313HZ 3 countries Android 4.4.2 (KitKat)

Samsung Galaxy S Duos3 G313HZDDU0AOD1 Firmware

Name: Samsung Galaxy S Duos3 (SM-G313HZ)
Brand: Samsung
Availability: InStock

Samsung Galaxy S Duos3 G313HZDDU0AOD1 is an Android 4.4.2 (KitKat) firmware for Bangladesh (BNG), Nepal (NPL), Sri Lanka (SLK). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G313HZDDU0AOC1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G313HZ is available: G313HZDBS0AQB1.

8.9/10 (452)13,014 times

Android 4.4.2 (KitKat)

OS Version

2015-04-07

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: G313HZDDU0AOD1

Model	Region	CSC Version	Release date	Size	File name	Download
SM-G313HZ	BNG Bangladesh NPL Nepal SLK Sri Lanka	G313HZODD0AOD1	2015-04-30	539.531 MiB	SM-G313HZ_1_20161024130741_i0fw8e1k26_fac.zip

Device specifications

Launched withAndroid 4.4.2
Display diagonal10.1 cm (3.97")
Display resolution480 x 800 pixels
Display typeTFT
RAM0.5 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
Battery capacity1500 mAh
Weight123.8 g

Specifications of SM-G313H, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

How to flash G313HZDDU0AOD1

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G313HZDDU0AOD1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G313HZDDU0AOD1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy S Duos3, released for Bangladesh (BNG), Nepal (NPL), Sri Lanka (SLK). Samsung built it on 2015-04-07.

No. A newer build for SM-G313HZ is available: G313HZDBS0AQB1. Install it instead of G313HZDDU0AOD1 unless you need this exact version. The previous build was G313HZDDU0AOC1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 539.531 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S Duos3 must be on bootloader binary 0 or lower.

This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy S Duos3 running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 26 other builds of this model use the same binary, so you can switch between them in both directions.