Samsung Galaxy S Duos3 G313HZDBU0AOG2
SM-G313HZ 1 country Android 4.4.2 (KitKat)

Samsung Galaxy S Duos3 G313HZDBU0AOG2 Firmware

Samsung Galaxy S Duos3 G313HZDBU0AOG2 is an Android 4.4.2 (KitKat) firmware for New Zealand (XNZ). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G313HZDBU0AOD1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G313HZ is available: G313HZDBS0AQB1.

Download firmware
8.7/10 (454)4,339 times
Android 4.4.2 (KitKat)
OS Version
2015-07-17
Build Date
1
Countries
1
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G313HZDBU0AOG2
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G313HZ
    XNZ New Zealand
    		G313HZ0AOG3 — — Download

    No matching downloads

    How to flash G313HZDBU0AOG2

    • G313HZDBU0AOG2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 4.4.2
    • Display diagonal10.1 cm (3.97")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • RAM0.5 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity1500 mAh
    • Weight123.8 g

    Specifications of SM-G313H, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G313HZDBU0AOG2 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy S Duos3, released for New Zealand (XNZ). Samsung built it on 2015-07-17.

    No. A newer build for SM-G313HZ is available: G313HZDBS0AQB1. Install it instead of G313HZDBU0AOG2 unless you need this exact version. The previous build was G313HZDBU0AOD1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy S Duos3 must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy S Duos3 running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 26 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S Duos3

    No changelog details available.
    Model firmware by region