Samsung Galaxy Ace 4 G313MUBU0ANK1
SM-G313M 1 country Android 4.4.2 (KitKat)

Samsung Galaxy Ace 4 G313MUBU0ANK1 Firmware

Samsung Galaxy Ace 4 G313MUBU0ANK1 is an Android 4.4.2 (KitKat) firmware for Brazil (ZTO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G313MUBU0ANI2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G313M is available: G313MUBU0AOI2.

Download firmware
9.2/10 (457)4,429 times
Android 4.4.2 (KitKat)
OS Version
2014-11-03
Build Date
1
Countries
1
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G313MUBU0ANK1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G313M
    ZTO Brazil
    		G313M0ANK1 — —

    No matching downloads

    How to flash G313MUBU0ANK1

    • G313MUBU0ANK1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 4.4
    • Display diagonal10.2 cm (4")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • Processor frequency1 GHz
    • RAM0.5 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Weight124 g

    Frequently Asked Questions

    G313MUBU0ANK1 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Ace 4, released for Brazil (ZTO). Samsung built it on 2014-11-03.

    No. A newer build for SM-G313M is available: G313MUBU0AOI2. Install it instead of G313MUBU0ANK1 unless you need this exact version. The previous build was G313MUBU0ANI2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Ace 4 must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Ace 4 running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 11 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Ace 4

    No changelog details available.
    Model firmware by region