Samsung Galaxy Ace4 Lite G318MZDXU0APF1
SM-G318MZ 2 countries Android 4.4.4 (KitKat)

Samsung Galaxy Ace4 Lite G318MZDXU0APF1 Firmware

Samsung Galaxy Ace4 Lite G318MZDXU0APF1 is an Android 4.4.4 (KitKat) firmware for Philippines (SMA, XTC, XTE), Thailand (THW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G318MZDXU0APB1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G318MZ is available: G318MZDXS0AQC1.

Download firmware
9.2/10 (463)17,874 times
Android 4.4.4 (KitKat)
OS Version
2016-06-10
Build Date
2
Countries
4
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: G318MZDXU0APF1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G318MZ
    SMA Philippines
    		G318MZOLC0APE1 — — Download
    SM-G318MZ
    THW Thailand
    		G318MZOLC0APE1 — — Download
    SM-G318MZ
    XTC Philippines
    		G318MZOLC0APE1 — — Download
    SM-G318MZ
    XTE Philippines
    		G318MZOLC0APE1 — — Download

    No matching downloads

    How to flash G318MZDXU0APF1

    • G318MZDXU0APF1 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal10.2 cm (4")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • RAM0.5 GB
    • Rear camera resolution3 MP
    • Rear camera typeSingle camera
    • Battery capacity1500 mAh
    • Weight123 g

    Specifications of SM-G318H, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G318MZDXU0APF1 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy Ace4 Lite, released for Philippines (SMA, XTC, XTE), Thailand (THW). Samsung built it on 2016-06-10.

    No. A newer build for SM-G318MZ is available: G318MZDXS0AQC1. Install it instead of G318MZDXU0APF1 unless you need this exact version. The previous build was G318MZDXU0APB1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Ace4 Lite must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Ace4 Lite running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 6 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Ace4 Lite

    No changelog details available.
    Model firmware by region