Samsung Galaxy Trend3 G3502IZNUAOF2
SM-G3502I 1 country Android 4.3 (Jelly)

Samsung Galaxy Trend3 G3502IZNUAOF2 Firmware

Samsung Galaxy Trend3 G3502IZNUAOF2 is an Android 4.3 (Jelly) firmware for China (CHU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G3502IZNUAOF1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G3502I is available: G3502IZNUAOK1.

Download firmware
9.0/10 (480)4,208 times
Android 4.3 (Jelly)
OS Version
2015-06-26
Build Date
1
Countries
1
CSC codes
U (30)
Bootloader binary

Bootloader binary U (30). Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G3502IZNUAOF2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G3502I
    CHU China
    		G3502ICHUAOF2 2015-07-04 634.873 MiB
    SM-G3502I_1_20160119140014_ig5h5x5wc7_fac.zip
    		Download

    No matching downloads

    How to flash G3502IZNUAOF2

    • G3502IZNUAOF2 has bootloader binary U (30). Your device must run binary U (30) or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 4.2
    • Display diagonal10.9 cm (4.3")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • RAM0.75 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity1800 mAh
    • Weight132.5 g

    Specifications of SM-G350, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G3502IZNUAOF2 is Android 4.3 (Jelly) firmware for Samsung Galaxy Trend3, released for China (CHU). Samsung built it on 2015-06-26.

    No. A newer build for SM-G3502I is available: G3502IZNUAOK1. Install it instead of G3502IZNUAOF2 unless you need this exact version. The previous build was G3502IZNUAOF1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 634.873 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Trend3 must be on bootloader binary U (30) or lower.

    This build uses bootloader binary U (30). It can be flashed on a Samsung Galaxy Trend3 running binary U (30) or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 4 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Trend3

    No changelog details available.
    Model firmware by region