Samsung Galaxy Core2 G355MUBU0ANL2
SM-G355M 4 countries Android 4.4.2 (KitKat)

Samsung Galaxy Core2 G355MUBU0ANL2 Firmware

Samsung Galaxy Core2 G355MUBU0ANL2 is an Android 4.4.2 (KitKat) firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G355MUBU0ANK2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G355M is available: G355MUBS0AQC2.

Download firmware
9.3/10 (461)17,409 times
Android 4.4.2 (KitKat)
OS Version
2014-12-05
Build Date
4
Countries
4
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionRelease dateSizeFile nameDownload
    SM-G355M
    CHL Chile
    		G355MUWA0ANK3G355MUMU0ANL1 2014-12-22 620.002 MiB
    SM-G355M_1_20170206125939_c8ybb138w7_fac.zip
    		Download
    SM-G355M
    PNT Peru
    		G355M0AOA2G355MUBU0ANL2 — — — Download
    SM-G355M
    TCE Mexico
    		G355M0ANK2G355MUBU0ANL2 — — — Download
    SM-G355M
    ZTA Brazil
    		G355M0ANL1G355MUBU0ANL2 — — — Download

    No matching downloads

    How to flash G355MUBU0ANL2

    • G355MUBU0ANL2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G355MUBU0ANL2 by region

    Samsung released this build in all regions (1) on the same day, December 22, 2014.

    Device specifications

    • Launched withAndroid 4.4
    • Display diagonal11.4 cm (4.5")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • RAM0.75 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity2000 mAh
    • Weight139 g

    Specifications of SM-G355, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G355MUBU0ANL2 is Android 4.4.2 (KitKat) firmware for Samsung Galaxy Core2, released for 4 countries, 4 CSC codes. Samsung built it on 2014-12-05.

    No. A newer build for SM-G355M is available: G355MUBS0AQC2. Install it instead of G355MUBU0ANL2 unless you need this exact version. The previous build was G355MUBU0ANK2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 620.002 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Core2 must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Core2 running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 61 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Core2

    No changelog details available.
    Model firmware by region