Samsung Galaxy Core Prime G3606ZNS1APF1
SM-G3606 1 country Android 4.4.4 (KitKat)

Samsung Galaxy Core Prime G3606ZNS1APF1 Firmware

Samsung Galaxy Core Prime G3606ZNS1APF1 is an Android 4.4.4 (KitKat) firmware for China (CHU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G3606ZNU1AOH2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G3606 is available: G3606ZNU1AQB1.

Download firmware
9.2/10 (459)4,342 times
Android 4.4.4 (KitKat)
OS Version
2016-06-16
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G3606ZNS1APF1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G3606
    CHU China
    		G36061APF1 — — Download

    No matching downloads

    How to flash G3606ZNS1APF1

    • G3606ZNS1APF1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal11.4 cm (4.5")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • RAM2 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity2000 mAh
    • Weight130 g

    Specifications of SM-G360F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G3606ZNS1APF1 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy Core Prime, released for China (CHU). Samsung built it on 2016-06-16.

    No. A newer build for SM-G3606 is available: G3606ZNU1AQB1. Install it instead of G3606ZNS1APF1 unless you need this exact version. The previous build was G3606ZNU1AOH2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Core Prime must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Core Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 7 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Core Prime

    The exact changes may differ depending on your device model, country/Region, and service provider.

    • Other bug fixes
    - Network connectivity enhancement.
    • The latest Android security patch has been applied.
    - Device security has been further enhanced.

    No changelog details available.
    Model firmware by region