Samsung Galaxy Core Prime G360GDVU1BQE2
SM-G360G 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy Core Prime G360GDVU1BQE2 Firmware

Samsung Galaxy Core Prime G360GDVU1BQE2 is an Android 5.1.1 (Lollipop) firmware for Australia (VAP). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G360GDXU1BQC2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. This is the newest build for SM-G360G.

Download firmware
9.4/10 (460)12,947 times
Android 5.1.1 (Lollipop)
OS Version
2017-05-22
First release
other regions until 2020-11-26
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-G360G
    VAP Australia
    		G360GVAP1BQE3G360GDVU1BTI2 2020-11-26 2017-06-23 780.967 MiB
    SM-G360G_1_20201126171034_y25ku7ezz9_fac.zip
    		Download
    SM-G360G
    VAP Australia
    		G360G1BQE3G360GDVU1BQE2 2017-05-22 2020-11-26 — — Download

    No matching downloads

    How to flash G360GDVU1BQE2

    • G360GDVU1BQE2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    What's new in G360GDVU1BQE2

    • Network connectivity enhancement.

    Device specifications

    • Display diagonal11.4 cm (4.5")
    • Display resolution480 x 800 pixels
    • Display typeTFT
    • RAM2 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity2000 mAh
    • Weight130 g

    Specifications of SM-G360F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G360GDVU1BQE2 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy Core Prime, released for Australia (VAP). Samsung built it on 2017-05-22.

    Yes. G360GDVU1BQE2 is the newest build for SM-G360G on SamFirm. The previous build was G360GDXU1BQC2.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 780.967 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Core Prime must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Core Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 29 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Core Prime

    • Network connectivity enhancement.

    No changelog details available.

    The exact changes may differ depending on your device model, country/Region, and service provider.

    • Other bug fixes
    - Network connectivity enhancement.
    • The latest Android security patch has been applied.
    - Device security has been further enhanced.

    No changelog details available.
    Model firmware by region