SM-G360P 1 country Android 4.4.4 (KitKat)

Samsung Galaxy Core Prime G360PVPU2AOF3 Firmware

Name: Samsung Galaxy Core Prime (SM-G360P)
Brand: Samsung
Availability: InStock

Samsung Galaxy Core Prime G360PVPU2AOF3 is an Android 4.4.4 (KitKat) firmware for United States (BST, VMU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G360PVPU0ANL8 https://samfirm.shop/build/G360PVPU0ANL8: bootloader binary raised from 0 to 2, so after installing it there is no way back to older builds. A newer build for SM-G360P is available: G360PVPS2AQD1 https://samfirm.shop/build/G360PVPS2AQD1.

9.1/10 (452)8,746 times

Android 4.4.4 (KitKat)

OS Version

n/a

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: G360PVPU2AOF3

Model	Region	CSC Version	Size	File name	Download
SM-G360P	BST United States	G360PSPT2AOF3	—	—
SM-G360P	VMU United States	G360PSPT2AOF3	—	—

Device specifications

Launched withAndroid 4.4
Display diagonal11.4 cm (4.5")
Display resolution480 x 800 pixels
Display typeTFT
Processor frequency1.2 GHz
RAM1 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity2000 mAh
Weight130 g

How to flash G360PVPU2AOF3

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G360PVPU2AOF3 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G360PVPU2AOF3 is Android 4.4.4 (KitKat) firmware for Samsung Galaxy Core Prime, released for United States (BST, VMU).

No. A newer build for SM-G360P is available: G360PVPS2AQD1. Install it instead of G360PVPU2AOF3 unless you need this exact version. The previous build was G360PVPU0ANL8.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Core Prime must be on bootloader binary 2 or lower.

This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy Core Prime running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 6 other builds of this model use the same binary, so you can switch between them in both directions.