Samsung Galaxy Core Prime G360T1UVU1APG2
SM-G360T1 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy Core Prime G360T1UVU1APG2 Firmware

Samsung Galaxy Core Prime G360T1UVU1APG2 is an Android 5.1.1 (Lollipop) firmware for United States (TMB). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G360T1UVU1AOFA, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G360T1 is available: G360T1UVS2ARI2.

Download firmware
9.4/10 (456)4,471 times
Android 5.1.1 (Lollipop)
OS Version
2016-07-13
Build Date
n/a
Security patch
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Core Prime use bootloader binary 2 (latest: G360T1UVS2ARI2). If your device already runs binary 2, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G360T1UVU1APG2
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G360T1
    TMB United States
    		G360T11APG2 — —

    No matching downloads

    How to flash G360T1UVU1APG2

    • G360T1UVU1APG2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 5.1
    • Display diagonal11.4 cm (4.5")
    • Display resolution480 x 800 pixels
    • RAM1 GB
    • Rear camera resolution5 MP
    • Rear camera typeSingle camera
    • Battery capacity2000 mAh

    Specifications of SM-G360T, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G360T1UVU1APG2 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy Core Prime, released for United States (TMB). Samsung built it on 2016-07-13.

    No. A newer build for SM-G360T1 is available: G360T1UVS2ARI2. Install it instead of G360T1UVU1APG2 unless you need this exact version. The previous build was G360T1UVU1AOFA.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Core Prime must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Core Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Core Prime

    No changelog details available.
    Model firmware by region