SM-G360T 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy Core Prime G360TUVU1APG2 Firmware

Name: Samsung Galaxy Core Prime (SM-G360T)
Brand: Samsung
Availability: InStock

Samsung Galaxy Core Prime G360TUVU1APG2 is an Android 5.1.1 (Lollipop) firmware for United States (TMB). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G360TUVU1APD2, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G360T is available: G360TUVU2AQD1.

8.9/10 (453)4,185 times

Android 5.1.1 (Lollipop)

OS Version

2016-07-13

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Core Prime use bootloader binary 2 (latest: G360TUVU2AQD1). If your device already runs binary 2, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: G360TUVU1APG2

Model	Region	CSC Version	Size	File name	Download
SM-G360T	TMB United States	G360T1APG2	—	—

Device specifications

Launched withAndroid 5.1
Display diagonal11.4 cm (4.5")
Display resolution480 x 800 pixels
Processor frequency1.2 GHz
RAM1 GB
Rear camera resolution5 MP
Rear camera typeSingle camera
Battery capacity2000 mAh

How to flash G360TUVU1APG2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G360TUVU1APG2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

G360TUVU1APG2 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy Core Prime, released for United States (TMB). Samsung built it on 2016-07-13.

No. A newer build for SM-G360T is available: G360TUVU2AQD1. Install it instead of G360TUVU1APG2 unless you need this exact version. The previous build was G360TUVU1APD2.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Core Prime must be on bootloader binary 1 or lower.

This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Core Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.