Samsung Galaxy Xcover4 G390WVLU1AQJ1
SM-G390W 1 country Android 7.0 (Nougat)

Samsung Galaxy Xcover4 G390WVLU1AQJ1 Firmware

Samsung Galaxy Xcover4 G390WVLU1AQJ1 is an Android 7.0 (Nougat) firmware for Canada (BMC, BWA, CHR, ESK, FMC, GLW, KDO, MTB, PMB, RWC, SPC, TLS, VMC, VTR, XAC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. A newer build for SM-G390W is available: G390WVLS2CTI2.

8.7/10 (471)65,252 times
Android 7.0 (Nougat)
OS Version
2017-10-30
Build Date
n/a
Security patch
1
Countries
15
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Xcover4 use bootloader binary 2 (latest: G390WVLS2CTI2). If your device already runs binary 2, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G390WVLU1AQJ1
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G390W
    BMC, BWA, CHR, ESK, FMC, GLW, KDO, MTB, PMB, RWC, SPC, TLS, VMC, VTR, XAC Canada
    		G390WOYA1AQJ1 2017-11-16 2.331 GiB
    SM-G390W_1_20201006150804_aultbrhrv0_fac.zip

    No matching downloads

    Device specifications

    • Launched withAndroid 7.0
    • Display diagonal12.7 cm (4.99")
    • Display resolution1280 x 720 pixels
    • Display typeTFT
    • RAM2 GB
    • RAM typeLPDDR3
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity2800 mAh
    • Weight172 g

    Specifications of SM-G390F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    How to flash G390WVLU1AQJ1

    • G390WVLU1AQJ1 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    G390WVLU1AQJ1 is Android 7.0 (Nougat) firmware for Samsung Galaxy Xcover4, released for Canada (BMC, BWA, CHR, ESK, FMC, GLW, KDO, MTB, PMB, RWC, SPC, TLS, VMC, VTR, XAC). Samsung built it on 2017-10-30.

    No. A newer build for SM-G390W is available: G390WVLS2CTI2. Install it instead of G390WVLU1AQJ1 unless you need this exact version.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.331 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Xcover4 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Xcover4 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Xcover4

    · Security patch update

    · The security of your device has been improved.

    Upgraded One UI for Android Pie

    One UI brings you Android Pie, with exciting new features and a whole new look and feel based on feedback from users in Samsung and Google.
    We recommend that you back up your important data to keep it safe before the upgrade.
    Some apps, including Calculator, Samsung Internet, and Samsung Notes, need to be updated individually after you update your OS.
    To use the Remote unlock function in Find My Mobile on an Android Pie device, the screen lock password (or PIN/pa...

    No changelog details available.
    No changelog details available.
    Show 1 older build
    No changelog details available.
    Model firmware by region