Samsung Galaxy Grand Prime G530WVLU1AOFB
SM-G530W 1 country Android 5.1.1 (Lollipop)

Samsung Galaxy Grand Prime G530WVLU1AOFB Firmware

Samsung Galaxy Grand Prime G530WVLU1AOFB is an Android 5.1.1 (Lollipop) firmware for Canada (BMC, BWA, ESK, FMC, GLW, KDO, MTA, PMB, RWC, SOL, SPC, TLS, VMC, VTR, XAC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G530WVLU1AOF9, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G530W is available: G530WVLS2AQB2.

Download firmware
9.2/10 (476)65,033 times
Android 5.1.1 (Lollipop)
OS Version
2015-08-21
Build Date
1
Countries
15
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy Grand Prime use bootloader binary 2 (latest: G530WVLS2AQB2). If your device already runs binary 2, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G530WVLU1AOFB
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G530W
    BMC, BWA, ESK, FMC, GLW, KDO, MTA, PMB, RWC, SOL, SPC, TLS, VMC, VTR, XAC Canada
    		G530WOYA1AOFB 2015-09-01 1012.209 MiB
    SM-G530W_1_20170302143452_t8hiepd0t7_fac.zip

    No matching downloads

    How to flash G530WVLU1AOFB

    • G530WVLU1AOFB has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G530WVLU1AOFB by region

    Samsung released this build in all regions (15) on the same day, September 1, 2015.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution540 x 960 pixels
    • Processor frequency1.2 GHz
    • RAM1.5 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2600 mAh
    • Weight156 g

    Frequently Asked Questions

    G530WVLU1AOFB is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy Grand Prime, released for Canada (BMC, BWA, ESK, FMC, GLW, KDO, MTA, PMB, RWC, SOL, SPC, TLS, VMC, VTR, XAC). Samsung built it on 2015-08-21.

    No. A newer build for SM-G530W is available: G530WVLS2AQB2. Install it instead of G530WVLU1AOFB unless you need this exact version. The previous build was G530WVLU1AOF9.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1012.209 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Grand Prime must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Grand Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Grand Prime

    No changelog details available.
    Model firmware by region