Samsung Galaxy Grand Prime G531HDDU0APG2
SM-G531H 2 countries Android 5.1.1

Samsung Galaxy Grand Prime G531HDDU0APG2 Firmware

Samsung Galaxy Grand Prime G531HDDU0APG2 is an Android 5.1.1 firmware for Bangladesh (BNG), Nepal (NPL). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G531HXXU0APG1: Android updated from Android 5.1.1 (Lollipop) to Android 5.1.1. A newer build for SM-G531H is available: G531HUBS0ARJ3.

Download firmware
9.4/10 (462)8,691 times
Android 5.1.1
OS Version
2016-07-15
Build Date
2
Countries
2
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: G531HDDU0APG2
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G531H
    BNG Bangladesh
    		G531HODD0APG2 — — Download
    SM-G531H
    NPL Nepal
    		G531HODD0APG2 — — Download

    No matching downloads

    How to flash G531HDDU0APG2

    • G531HDDU0APG2 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution540 x 960 pixels
    • Display typeTFT
    • Processor frequency1.2 GHz
    • RAM1 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2600 mAh
    • Weight156 g

    Frequently Asked Questions

    G531HDDU0APG2 is Android 5.1.1 firmware for Samsung Galaxy Grand Prime, released for Bangladesh (BNG), Nepal (NPL). Samsung built it on 2016-07-15.

    No. A newer build for SM-G531H is available: G531HUBS0ARJ3. Install it instead of G531HDDU0APG2 unless you need this exact version. The previous build was G531HXXU0APG1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Grand Prime must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Grand Prime running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 81 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Grand Prime

    No changelog details available.
    Model firmware by region