Samsung Galaxy Grand Prime G531HUBU0AOF8
SM-G531H 3 countries Android 5.1.1 (Lollipop)

Samsung Galaxy Grand Prime G531HUBU0AOF8 Firmware

Samsung Galaxy Grand Prime G531HUBU0AOF8 is an Android 5.1.1 (Lollipop) firmware for Panama (TPA), Trinidad & Tobago (TTT), Uruguay (UPO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G531HXXU0AOF8, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G531H is available: G531HUBS0ARJ3.

Download firmware
9.3/10 (461)12,818 times
Android 5.1.1 (Lollipop)
OS Version
2015-06-19
Build Date
3
Countries
3
CSC codes
0
Bootloader binary

Bootloader binary 0. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G531HUBU0AOF8
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G531H
    TPA Panama
    TTT Trinidad & Tobago
    UPO Uruguay
    		G531HUUB0AOF8 2015-07-09 733.14 MiB
    SM-G531H_1_20181218125240_n8r04wmr3j_fac.zip
    		Download

    No matching downloads

    How to flash G531HUBU0AOF8

    • G531HUBU0AOF8 has bootloader binary 0. Your device must run binary 0 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G531HUBU0AOF8 by region

    Samsung released this build in all regions (3) on the same day, July 9, 2015.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution540 x 960 pixels
    • Display typeTFT
    • Processor frequency1.2 GHz
    • RAM1 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity2600 mAh
    • Weight156 g

    Frequently Asked Questions

    G531HUBU0AOF8 is Android 5.1.1 (Lollipop) firmware for Samsung Galaxy Grand Prime, released for Panama (TPA), Trinidad & Tobago (TTT), Uruguay (UPO). Samsung built it on 2015-06-19.

    No. A newer build for SM-G531H is available: G531HUBS0ARJ3. Install it instead of G531HUBU0AOF8 unless you need this exact version. The previous build was G531HXXU0AOF8.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 733.14 MiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy Grand Prime must be on bootloader binary 0 or lower.

    This build uses bootloader binary 0. It can be flashed on a Samsung Galaxy Grand Prime running binary 0 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 81 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Grand Prime

    No changelog details available.
    Model firmware by region