Samsung Galaxy Grand Prime Plus G532FXWU1APK3
SM-G532F 1 country Android 6.0.1 (Marshmallow)

Samsung Galaxy Grand Prime Plus G532FXWU1APK3 Firmware

Samsung Galaxy Grand Prime Plus G532FXWU1APK3 is an Android 6.0.1 (Marshmallow) firmware for Pakistan (PAK). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G532FXXU1APJ9, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G532F is available: G532FXWU1ASB1.

Download firmware
9.4/10 (454)4,345 times
Android 6.0.1 (Marshmallow)
OS Version
2016-11-10
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G532FXWU1APK3
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G532F
    PAK Pakistan
    		G532FOJV1APK3 — — Download

    No matching downloads

    How to flash G532FXWU1APK3

    • G532FXWU1APK3 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution540 x 960 pixels
    • Display typePLS
    • Processor frequency1.4 GHz
    • RAM1.5 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsHybrid dual SIM
    • Battery capacity2600 mAh
    • Weight160 g

    Frequently Asked Questions

    G532FXWU1APK3 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy Grand Prime Plus, released for Pakistan (PAK). Samsung built it on 2016-11-10.

    No. A newer build for SM-G532F is available: G532FXWU1ASB1. Install it instead of G532FXWU1APK3 unless you need this exact version. The previous build was G532FXXU1APJ9.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy Grand Prime Plus must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy Grand Prime Plus running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 29 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy Grand Prime Plus

    · Security patch update
    No changelog details available.
    Model firmware by region