Samsung Galaxy J2 Prime G532MUBU1APJ2
SM-G532M 1 country Android 6.0.1 (Marshmallow)

Samsung Galaxy J2 Prime G532MUBU1APJ2 Firmware

Samsung Galaxy J2 Prime G532MUBU1APJ2 is an Android 6.0.1 (Marshmallow) firmware for Mexico (IUS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G532MUMU1APIG: Android updated from Android 6.0.1 to Android 6.0.1 (Marshmallow). A newer build for SM-G532M is available: G532MUMU1ASK1.

Download firmware
9.2/10 (457)4,457 times
Android 6.0.1 (Marshmallow)
OS Version
2016-10-09
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G532MUBU1APJ2
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G532M
    IUS Mexico
    		G532M1APJ2 — —

    No matching downloads

    How to flash G532MUBU1APJ2

    • G532MUBU1APJ2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 6.0
    • Display diagonal12.7 cm (5")
    • Display resolution960 x 540 pixels
    • Display typePLS
    • Processor frequency1.4 GHz
    • Processor familyMediaTek
    • Processor modelMT6737T
    • RAM1.5 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity2600 mAh
    • Weight160 g

    Frequently Asked Questions

    G532MUBU1APJ2 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy J2 Prime, released for Mexico (IUS). Samsung built it on 2016-10-09.

    No. A newer build for SM-G532M is available: G532MUMU1ASK1. Install it instead of G532MUBU1APJ2 unless you need this exact version. The previous build was G532MUMU1APIG.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J2 Prime must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy J2 Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 83 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J2 Prime

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Show 11 older builds

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region