Samsung Galaxy J2 Prime G532MUMU1ARE2
SM-G532M 4 countries Android 6.0.1 (Marshmallow)

Samsung Galaxy J2 Prime G532MUMU1ARE2 Firmware

Samsung Galaxy J2 Prime G532MUMU1ARE2 is an Android 6.0.1 (Marshmallow) firmware for 4 countries, 4 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G532MUBU1ARE1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G532M is available: G532MUMU1ASK1.

Download firmware
9.0/10 (463)21,909 times
Android 6.0.1 (Marshmallow)
OS Version
2018-05-09
Build Date
4
Countries
4
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionRelease dateSizeFile nameDownload
    SM-G532M
    ARO Argentina
    		G532MUUB1ARE1G532MUBU1ARD2 2018-06-01 1.49 GiB
    SM-G532M_1_20190309103714_dgq0cczgci_fac.zip
    MD5:f9cb15203f5d573e4026ad65d947ec10
    SHA1:1bc4ca9489c4d33f4504cbfe07e4749f65106aee
    		Download
    SM-G532M
    CWW Jamaica
    		G532MUWE1ARE1G532MUBU1ARD2 2018-09-12 1.617 GiB
    SM-G532M_1_20190307174327_hkuxg00dpw_fac.zip
    		Download
    SM-G532M
    PNT Peru
    		G532M1ARE1G532MUMU1ARE2 — — — Download
    SM-G532M
    PNT Peru
    		G532MPNT1ARE1G532MUBU1ARE1 2018-05-30 1.412 GiB
    SM-G532M_1_20190323144427_ij2vfvtd3t_fac.zip
    		Download
    SM-G532M
    ZTO Brazil
    		G532M1ARE1G532MUMU1ARE2 — — — Download

    No matching downloads

    How to flash G532MUMU1ARE2

    • G532MUMU1ARE2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G532MUMU1ARE2 by region

    First release
    May 30, 2018
    Last region
    September 12, 2018
    Duration
    106 days
    Regions
    3
    1. Day 1 · · 1 region
      PeruPNT
    2. Day 3 · · 1 region
      ArgentinaARO
    3. Day 106 · · 1 region
      JamaicaCWW

    Device specifications

    • Launched withAndroid 6.0
    • Display diagonal12.7 cm (5")
    • Display resolution960 x 540 pixels
    • Display typePLS
    • Processor frequency1.4 GHz
    • Processor familyMediaTek
    • Processor modelMT6737T
    • RAM1.5 GB
    • Rear camera resolution8 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity2600 mAh
    • Weight160 g

    Frequently Asked Questions

    G532MUMU1ARE2 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy J2 Prime, released for 4 countries, 4 CSC codes. Samsung built it on 2018-05-09.

    No. A newer build for SM-G532M is available: G532MUMU1ASK1. Install it instead of G532MUMU1ARE2 unless you need this exact version. The previous build was G532MUBU1ARE1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J2 Prime must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy J2 Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 83 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J2 Prime

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Show 11 older builds

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Model firmware by region