Samsung Galaxy J5 Prime G570FDDS3CTE1 Firmware
Samsung Galaxy J5 Prime G570FDDS3CTE1 is an Android 8.0.0 (Oreo) firmware for India (INS). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G570FXXU2CSL3: bootloader binary raised from 2 to 3, so after installing it there is no way back to older builds. A newer build for SM-G570F is available: G570FXXS4CTJA.
8.9/10 (475)4,431 times
Android 8.0.0 (Oreo)
OS Version
2020-06-05
Build Date
n/a
Security patch
1
Countries
1
CSC codes
3
Bootloader binary
Bootloader binary 3. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.
Newer builds of Samsung Galaxy J5 Prime use bootloader binary 4 (latest: G570FXXS4CTJA). If your device already runs binary 4, this build cannot be flashed.
All regional downloads
Pick your region (CSC) to download the matching firmware package.
Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
MODEM/CP Version: G570FDDS3CTD1
Device specifications
- Display diagonal12.7 cm (5")
- Display resolution1280 x 720 pixels
- Display typeTFT
- Processor frequency1.4 GHz
- RAM2 GB
- Rear camera resolution13 MP
- Rear camera typeSingle camera
- Battery capacity2400 mAh
- Weight143 g
How to flash G570FDDS3CTE1
- Install Samsung USB Drivers:Download Official Drivers
- Download Odin Flash Tool:
- G570FDDS3CTE1 has bootloader binary 3. Your device must run binary 3 or lower: it is the 5th character from the end of your current build number.
- CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
- HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
- The Download Mode key combo depends on the model: see all combos.
Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.
Frequently Asked Questions
G570FDDS3CTE1 is Android 8.0.0 (Oreo) firmware for Samsung Galaxy J5 Prime, released for India (INS). Samsung built it on 2020-06-05.
No. A newer build for SM-G570F is available: G570FXXS4CTJA. Install it instead of G570FDDS3CTE1 unless you need this exact version. The previous build was G570FXXU2CSL3.
Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.266 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J5 Prime must be on bootloader binary 3 or lower.
This build uses bootloader binary 3. It can be flashed on a Samsung Galaxy J5 Prime running binary 3 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 10 other builds of this model use the same binary, so you can switch between them in both directions.
Other builds and changelog for Samsung Galaxy J5 Prime
Show 15 older builds
No changelog details available.
· The security of your device has been improved.
※ If your device is encrypted, it must be decrypted before upgrading.