Samsung Galaxy J5 Prime G570MUBU1APL7
SM-G570M 1 country Android 6.0.1 (Marshmallow)

Samsung Galaxy J5 Prime G570MUBU1APL7 Firmware

Samsung Galaxy J5 Prime G570MUBU1APL7 is an Android 6.0.1 (Marshmallow) firmware for Ecuador (EBE). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G570MUBU1APL4, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G570M is available: G570MUBS9CTJ3.

Download firmware
8.7/10 (480)4,371 times
Android 6.0.1 (Marshmallow)
OS Version
2016-12-29
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J5 Prime use bootloader binary 9 (latest: G570MUBS9CTJ3). If your device already runs binary 9, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G570MUBU1APL2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G570M
    EBE Ecuador
    		G570MUWT1APL1 2017-01-19 2.272 GiB
    SM-G570M_1_20200813070833_0sewsd9wy1_fac.zip
    		Download

    No matching downloads

    How to flash G570MUBU1APL7

    • G570MUBU1APL7 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal12.7 cm (5")
    • Display resolution1280 x 720 pixels
    • Display typeTFT
    • RAM2 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity2400 mAh
    • Weight143 g

    Specifications of SM-G570F, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G570MUBU1APL7 is Android 6.0.1 (Marshmallow) firmware for Samsung Galaxy J5 Prime, released for Ecuador (EBE). Samsung built it on 2016-12-29.

    No. A newer build for SM-G570M is available: G570MUBS9CTJ3. Install it instead of G570MUBU1APL7 unless you need this exact version. The previous build was G570MUBU1APL4.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.272 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy J5 Prime must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy J5 Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 13 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J5 Prime

    No changelog details available.
    Model firmware by region