Samsung Galaxy J7 Prime G610FDXU1API4
SM-G610F 1 country Android 6.0.1 (Nougat)

Samsung Galaxy J7 Prime G610FDXU1API4 Firmware

Samsung Galaxy J7 Prime G610FDXU1API4 is an Android 6.0.1 (Nougat) firmware for Singapore (XSP). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G610FXXU1API4: Android updated from Android 6.0.1 (Oreo) to Android 6.0.1 (Nougat). A newer build for SM-G610F is available: G610FDDU1CTG2.

9.3/10 (453)4,295 times
Android 6.0.1 (Nougat)
OS Version
2016-09-08
Build Date
n/a
Security patch
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G610FDXU1API4
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G610F
    XSP Singapore
    		G610FOLB1API5 — —

    No matching downloads

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1920 x 1080 pixels
    • Display typeTFT
    • Processor frequency1.6 GHz
    • RAM3 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • SIM cardsDual SIM
    • Battery capacity3300 mAh
    • Weight167 g

    How to flash G610FDXU1API4

    • G610FDXU1API4 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    G610FDXU1API4 is Android 6.0.1 (Nougat) firmware for Samsung Galaxy J7 Prime, released for Singapore (XSP). Samsung built it on 2016-09-08.

    No. A newer build for SM-G610F is available: G610FDDU1CTG2. Install it instead of G610FDXU1API4 unless you need this exact version. The previous build was G610FXXU1API4.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J7 Prime must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy J7 Prime running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 116 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7 Prime

    No changelog details available.
    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · The security of your device has been improved.

    Show 15 older builds

    · The security of your device has been improved.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    No changelog details available.

    · The security of your device has been improved.

    No changelog details available.
    No changelog details available.
    No changelog details available.

    · The security of your device has been improved.

    ※ If your device is encrypted, it must be decrypted before upgrading.

    · The security of your device has been improved.

    ※ If your device is encrypted, it must be decrypted before upgrading.

    · The security of your device has been improved.

    ※ If your device is encrypted, it must be decrypted before upgrading.

    · The security of your device has been improved.

    ※ If your device is encrypted, it must be decrypted before upgrading.

    · The security of your device has been improved.

    No changelog details available.
    No changelog details available.
    Model firmware by region