Samsung Galaxy J7 Prime G610MUBU5CSD7
SM-G610M 3 countries Android 8.1.0 (Oreo)

Samsung Galaxy J7 Prime G610MUBU5CSD7 Firmware

Samsung Galaxy J7 Prime G610MUBU5CSD7 is an Android 8.1.0 (Oreo) firmware for Argentina (CTI), Panama (PCW), Uruguay (CTU). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G610MUBU5CSD6, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G610M is available: G610MUBS8CTH4.

8.7/10 (29)13,475 times
Android 8.1.0 (Oreo)
OS Version
2019-05-07
First release
other regions until 2019-07-16
2019-05-01
Security patch
3
Countries
3
CSC codes
5
Bootloader binary

Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy J7 Prime use bootloader binary 8 (latest: G610MUBS8CTH4). If your device already runs binary 8, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-G610M
    CTI Argentina
    CTU Uruguay
    		G610MUWA5CSE1G610MUBU5CSF1 2019-06-15 2019-07-20 2.588 GiB
    SM-G610M_1_20190615033653_cvmph44oka_fac.zip
    SM-G610M
    CTI Argentina
    		G610MUWA5CSE1G610MUBU5CSD7 2019-05-07 2019-07-20 — —
    SM-G610M
    CTU Uruguay
    		G610MUWA5CSE1G610MUBU5CSD7 2019-05-07 2019-07-20 — —
    SM-G610M
    PCW Panama
    		G610MUUB5CSF1G610MUBU5CSF1 2019-07-16 2019-07-20 2.339 GiB
    SM-G610M_1_20190716023927_bqv0gad33s_fac.zip
    SM-G610M
    PCW Panama
    		G610MUUB5CSF1G610MUBU5CSD7 2019-05-07 2019-07-20 — —

    No matching downloads

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1920 x 1080 pixels
    • Display typeTFT
    • RAM3 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3300 mAh
    • Weight167 g

    Specifications of SM-G610, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    What's new in G610MUBU5CSD7

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    How to flash G610MUBU5CSD7

    • G610MUBU5CSD7 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    G610MUBU5CSD7 is Android 8.1.0 (Oreo) firmware for Samsung Galaxy J7 Prime, released for Argentina (CTI), Panama (PCW), Uruguay (CTU). It includes the 2019-05-01 security patch. Samsung built it on 2019-05-07.

    No. A newer build for SM-G610M is available: G610MUBS8CTH4. Install it instead of G610MUBU5CSD7 unless you need this exact version. The previous build was G610MUBU5CSD6.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J7 Prime must be on bootloader binary 5 or lower.

    This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy J7 Prime running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7 Prime

    No changelog details available.
    No changelog details available.
    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Show 15 older builds
    No changelog details available.
    No changelog details available.
    No changelog details available.
    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    No changelog details available.
    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · Security patch update
    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    Model firmware by region