Samsung Galaxy J7 Prime G610MUBS8CTH3
SM-G610M 3 countries Android 8.1.0 (Oreo)

Samsung Galaxy J7 Prime G610MUBS8CTH3 Firmware

Samsung Galaxy J7 Prime G610MUBS8CTH3 is an Android 8.1.0 (Oreo) firmware for Chile (CHK, CHO, CHP, CHQ, CHT), Colombia (COB, COE), Ecuador (EBE). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G610MUBS8CTH1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G610M is available: G610MUBS8CTH4.

Download firmware
9.2/10 (460)34,956 times
Android 8.1.0 (Oreo)
OS Version
2020-08-18
First release
other regions until 2020-10-09
3
Countries
8
CSC codes
8
Bootloader binary

Bootloader binary 8. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    Your CSC is in Settings → About phone (About tablet) → Software information, or dial *#1234#. The CSC sets your region's features and network bands. Download the firmware for your country.
    MODEM/CP Version: G610MUBS8CTH1
    ModelRegionCSC VersionBuild DateRelease dateSizeFile nameDownload
    SM-G610M
    CHK, CHO, CHP, CHQ Chile
    		G610MUUB8CTH1 2020-08-18 2020-08-25 2.293 GiB
    SM-G610M_1_20200818221733_zoemsweo0r_fac.zip
    		Download
    SM-G610M
    CHT Chile
    COB Colombia
    EBE Ecuador
    		G610MUWT8CTH1 2020-08-22 2020-09-07 2.496 GiB
    SM-G610M_1_20200822051503_79br7gyjve_fac.zip
    		Download
    SM-G610M
    COE Colombia
    		G610MUWC8CTH1 2020-10-09 2020-10-12 2.29 GiB
    SM-G610M_1_20200825040534_m7t9hbuxvh_fac.zip
    		Download

    No matching downloads

    How to flash G610MUBS8CTH3

    • G610MUBS8CTH3 has bootloader binary 8. Your device must run binary 8 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G610MUBS8CTH3 by region

    First release
    August 25, 2020
    Last region
    October 12, 2020
    Duration
    49 days
    Regions
    8
    1. Day 1 · · 1 region
      ChileCHO
    2. Day 2 · · 3 regions
      ChileCHKCHPCHQ
    3. Day 14 · · 1 region
      ColombiaCOB
    4. Day 17 · · 1 region
      ChileCHT
    5. Day 19 · · 1 region
      EcuadorEBE
    6. Day 49 · · 1 region
      ColombiaCOE

    Device specifications

    • Display diagonal14 cm (5.5")
    • Display resolution1920 x 1080 pixels
    • Display typeTFT
    • RAM3 GB
    • Rear camera resolution13 MP
    • Rear camera typeSingle camera
    • Battery capacity3300 mAh
    • Weight167 g

    Specifications of SM-G610, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G610MUBS8CTH3 is Android 8.1.0 (Oreo) firmware for Samsung Galaxy J7 Prime, released for Chile (CHK, CHO, CHP, CHQ, CHT), Colombia (COB, COE), Ecuador (EBE). Samsung built it on 2020-08-18.

    No. A newer build for SM-G610M is available: G610MUBS8CTH4. Install it instead of G610MUBS8CTH3 unless you need this exact version. The previous build was G610MUBS8CTH1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The Samsung Galaxy J7 Prime must be on bootloader binary 8 or lower.

    This build uses bootloader binary 8. It can be flashed on a Samsung Galaxy J7 Prime running binary 8 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 3 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy J7 Prime

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    No changelog details available.
    Show 7 older builds

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    · Security patch update
    No changelog details available.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    Model firmware by region