Samsung Galaxy XCover Pro G715FNXXS2ATA2
SM-G715FN 19 countries Android 10

Samsung Galaxy XCover Pro G715FNXXS2ATA2 Firmware

Samsung Galaxy XCover Pro G715FNXXS2ATA2 is an Android 10 firmware for 19 countries, 19 CSC codes. It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G715FNXXU1ATA1: bootloader binary raised from 1 to 2, so after installing it there is no way back to older builds; security patch 2020-02-01 instead of 2020-01-01. A newer build for SM-G715FN is available: G715FNXXSDFXA1.

OS updates guaranteed until: Android 13Security updates until: Jan 1, 2024
Download firmware
9.1/10 (478)82,187 times
Android 10
OS Version
2020-01-22
First release
other regions until 2020-01-23
2020-02-01
Security patch
19
Countries
19
CSC codes
2
Bootloader binary

Bootloader binary 2. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy XCover Pro use bootloader binary D (13) (latest: G715FNXXSDFXA1). If your device already runs binary D (13), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G715FNXXS2ATA2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G715FN
    ATO Austria
    AUT Switzerland
    BGL Bulgaria
    BTU United Kingdom
    +15 more countries
    DBT Germany
    EUR Greece
    ITV Italy
    LUX Luxembourg
    NEE Nordic Europe
    ORX Slovakia
    PHE Spain
    PHN Netherlands
    SEB Baltic Europe
    SIO Slovenia
    TPH Portugal
    XEF France
    XEH Hungary
    XEO Poland
    XEZ Czechia
    		G715FNOXM2ATA3, G715FNOXM2ATA2 2020-01-31 4.67 GiB
    SM-G715FN_1_20220218231100_ms4qqq7mud_fac.zip
    MD5:cbcc5e2f721ce29c159e5b9245ae1a2d
    SHA1:3b35c9a347d1cc6cef0f73c76a6ba5cc95aaeac7
    		Download

    No matching downloads

    How to flash G715FNXXS2ATA2

    • G715FNXXS2ATA2 has bootloader binary 2. Your device must run binary 2 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    What's new in G715FNXXS2ATA2

    · The security of your device has been improved.

    Rollout of G715FNXXS2ATA2 by region

    First release
    January 31, 2020
    Last region
    February 4, 2020
    Duration
    5 days
    Regions
    19
    1. Day 1 · · 1 region
      PolandXEO
    2. Day 4 · · 14 regions
      AustriaATOBaltic EuropeSEBBulgariaBGLGermanyDBTItalyITVLuxembourgLUXNetherlandsPHNNordic EuropeNEEPortugalTPHSlovakiaORXSloveniaSIOSpainPHE
      +2 more countries
      SwitzerlandAUTUnited KingdomBTU
    3. Day 5 · · 4 regions
      CzechiaXEZFranceXEFGreeceEURHungaryXEH

    Device specifications

    • Display diagonal16 cm (6.3")
    • Display resolution2340 x 1080 pixels
    • Processor frequency2.3 GHz
    • Processor familySamsung Exynos
    • RAM4 GB
    • Rear camera resolution25 MP
    • Rear camera typeDual camera
    • SIM cardsDual SIM
    • Battery capacity4050 mAh
    • Weight218 g

    Frequently Asked Questions

    G715FNXXS2ATA2 is Android 10 firmware for Samsung Galaxy XCover Pro, released for 19 countries, 19 CSC codes. It includes the 2020-02-01 security patch. Samsung built it on 2020-01-22.

    No. A newer build for SM-G715FN is available: G715FNXXSDFXA1. Install it instead of G715FNXXS2ATA2 unless you need this exact version. The previous build was G715FNXXU1ATA1.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 4.67 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy XCover Pro must be on bootloader binary 2 or lower.

    This build uses bootloader binary 2. It can be flashed on a Samsung Galaxy XCover Pro running binary 2 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy XCover Pro

    • The security of your device has been improved.

    • Security
    The device is protected with improved security.

    • Stability and reliability
    Device behavior has been improved.

    • Security
    The device is protected with improved security.

    • Stability and reliability
    Device behavior has been improved.
    • Security
    The device is protected with improved security.

    Show 15 older builds
    One UI 5.1 Update

    One UI 5.1 takes your phone to the next level with new Gallery features as well as productivity and personalization enhancements.

    Gallery

    More powerful search
    You can now search your Gallery for more than one person or subject at the same time. You can even search for people without tagging their names just by tapping their faces.

    Revamped info display
    When you swipe up while viewing a picture or video in your Gallery, you can see when and where the picture was taken, whi...

    • The security of your device has been improved.

    • Maintenance mode
    Protect your privacy when someone else is using your phone, such as when you send it in for repairs. Maintenance mode prevents your pictures, messages, accounts, and other personal data from being accessed.
    • Stability and reliability
    Device behavior has been improved.
    • Security
    The device is protected with improved security.

    • Stability and reliability
    Device behavior has been improved.

    • The security of your device has been improved.

    One UI 5 Upgrade (Android 13)

    One UI 5 brings you more powerful personalization and makes it easier to get things done across your Galaxy devices.

    Visual design

    New app icons and illustrations
    Icon symbols are larger for a bolder look that's easier to scan. Subtle background gradients and improved contrast give a fresher, more natural feel. New help illustrations have been created to give a consistent look to all apps.

    Smoother than ever before
    New animations and transition effects make sw...

    • The security of your device has been improved.

    • Stability and reliability
    Device behavior has been improved.
    • Security
    The device is protected with improved security.

    • The security of your device has been improved.

    · The security of your device has been improved.

    One UI 4.1 Upgrade (Android 12)

    One UI 4.1 brings you a wide array of new features and enhancements for your Galaxy devices. More intuitive, more fun, more secure, and easier than ever.

    Check out the changes below.

    Color palette

    Customize your phone with unique colors based on your wallpaper. Your colors will be applied to menus, buttons, backgrounds, and apps throughout your phone.

    Privacy

    One UI 4.1 offers strong privacy protection to make sure your personal information doesn’t fall in...

    Model firmware by region