Samsung Galaxy XCover7 Pro G766NKSS4BYL1
SM-G766N 1 country Android 16

Samsung Galaxy XCover7 Pro G766NKSS4BYL1 Firmware

Samsung Galaxy XCover7 Pro G766NKSS4BYL1 is an Android 16 firmware for South Korea (KOO). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. A newer build for SM-G766N is available: G766NKSUBDZJ7.

OS updates guaranteed until: Android 22Security updates until: May 31, 2032
Download firmware
9.3/10 (40)101 times
Android 16
OS Version
2025-12-02
Build Date
1
Countries
1
CSC codes
4
Bootloader binary

Bootloader binary 4. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy XCover7 Pro use bootloader binary B (11) (latest: G766NKSUBDZJ7). If your device already runs binary B (11), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G766NKSS4BYK2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G766N
    KOO South Korea
    		G766NKOO4BYL1 2025-12-11 7.234 GiB
    SM-G766N_2_20251202141040_uc9uddpk4l_fac.zip
    		Download

    No matching downloads

    How to flash G766NKSS4BYL1

    • G766NKSS4BYL1 has bootloader binary 4. Your device must run binary 4 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Display diagonal16.8 cm (6.6")
    • Display resolution2408 x 1080 pixels
    • RAM6 GB
    • Rear camera resolution50 MP
    • Rear camera typeDual camera
    • Battery capacity4350 mAh
    • Weight240 g

    Specifications of SM-G766B, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G766NKSS4BYL1 is Android 16 firmware for Samsung Galaxy XCover7 Pro, released for South Korea (KOO). Samsung built it on 2025-12-02.

    No. A newer build for SM-G766N is available: G766NKSUBDZJ7. Install it instead of G766NKSS4BYL1 unless you need this exact version.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 7.234 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy XCover7 Pro must be on bootloader binary 4 or lower.

    This build uses bootloader binary 4. It can be flashed on a Samsung Galaxy XCover7 Pro running binary 4 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". No other build of this model uses binary 4.

    Other builds and changelog for Samsung Galaxy XCover7 Pro

    No changelog details available.
    Model firmware by region