Samsung Galaxy S20 FE 5G G781NKSS6GXF2
SM-G781N 1 country Android 13

Samsung Galaxy S20 FE 5G G781NKSS6GXF2 Firmware

Samsung Galaxy S20 FE 5G G781NKSS6GXF2 is an Android 13 firmware for South Korea (KOO, KTC, SKC). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G781NKSS6GXE5, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G781N is available: G781NKSSDGYJ1.

OS updates guaranteed until: Android 13Security updates until: Oct 28, 2025
Download firmware
9.3/10 (453)7,839 times
Android 13
OS Version
2024-06-27
Build Date
1
Countries
3
CSC codes
6
Bootloader binary

Bootloader binary 6. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S20 FE 5G use bootloader binary D (13) (latest: G781NKSSDGYJ1). If your device already runs binary D (13), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G781NKSS6GXF2
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G781N
    KOO, KTC, SKC South Korea
    		G781NOKR6GXF2 2024-06-27 6.772 GiB
    SM-G781N_3_20240612140241_zchx9iljur_fac.zip

    No matching downloads

    How to flash G781NKSS6GXF2

    • G781NKSS6GXF2 has bootloader binary 6. Your device must run binary 6 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Rollout of G781NKSS6GXF2 by region

    Samsung released this build in all regions (3) on the same day, June 27, 2024.

    Device specifications

    • Launched withAndroid 10.0
    • Display diagonal16.5 cm (6.5")
    • Display resolution2400 x 1080 pixels
    • Display typeSAMOLED
    • RAM6 GB
    • RAM typeLPDDR5
    • Rear camera resolution12 MP
    • Rear camera typeTriple camera
    • Battery capacity4500 mAh
    • Weight190 g

    Specifications of SM-G781B, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G781NKSS6GXF2 is Android 13 firmware for Samsung Galaxy S20 FE 5G, released for South Korea (KOO, KTC, SKC). Samsung built it on 2024-06-27.

    No. A newer build for SM-G781N is available: G781NKSSDGYJ1. Install it instead of G781NKSS6GXF2 unless you need this exact version. The previous build was G781NKSS6GXE5.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 6.772 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S20 FE 5G must be on bootloader binary 6 or lower.

    This build uses bootloader binary 6. It can be flashed on a Samsung Galaxy S20 FE 5G running binary 6 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S20 FE 5G

    No changelog details available.
    Model firmware by region