Samsung Galaxy S20 FE 5G G781VSQU1ATII
SM-G781V 1 country Android 10

Samsung Galaxy S20 FE 5G G781VSQU1ATII Firmware

Samsung Galaxy S20 FE 5G G781VSQU1ATII is an Android 10 firmware for United States (VZW). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G781VSQU1ATI9, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G781V is available: G781VSQSLHYI1.

OS updates guaranteed until: Android 13Security updates until: Oct 29, 2025
Download firmware
8.9/10 (457)4,430 times
Android 10
OS Version
2020-09-14
Build Date
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S20 FE 5G use bootloader binary L (21) (latest: G781VSQSLHYI1). If your device already runs binary L (21), this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G781VSQU1ATII
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G781V
    VZW United States
    		G781VOYN1ATII 2020-09-30 5.95 GiB
    SM-G781V_1_20211025125206_z9mrwskkiy_fac.zip

    No matching downloads

    How to flash G781VSQU1ATII

    • G781VSQU1ATII has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 10.0
    • Display diagonal16.5 cm (6.5")
    • Display resolution2400 x 1080 pixels
    • Display typeSAMOLED
    • RAM6 GB
    • RAM typeLPDDR5
    • Rear camera resolution12 MP
    • Rear camera typeTriple camera
    • Battery capacity4500 mAh
    • Weight190 g

    Specifications of SM-G781B, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G781VSQU1ATII is Android 10 firmware for Samsung Galaxy S20 FE 5G, released for United States (VZW). Samsung built it on 2020-09-14.

    No. A newer build for SM-G781V is available: G781VSQSLHYI1. Install it instead of G781VSQU1ATII unless you need this exact version. The previous build was G781VSQU1ATI9.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 5.95 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S20 FE 5G must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy S20 FE 5G running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S20 FE 5G

    • Security
    The device is protected with improved security.

    These changes may vary depending on the model, country, or network operator of the customer environment.

    • The security of your device has been improved.

    • Security
    The device is protected with improved security.

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    • Security
    The device is protected with improved security.

    Show 10 older builds

    · Device stability improvements, bug fixes.
    · New and / or enhanced features.
    · Further improvements to performance.

    • The security of your device has been improved.

    One UI 5.1.1 Update
    Multitasking

    Better app previews on the Recents screen
    The Recents screen now shows apps as they will appear after you open them. You can easily see if an app is opened in split screen, full screen, or as a pop-up.

    Easily switch from pop-up view to split screen
    Press and hold the handle at the top of the pop-up window, then drag the app to the side of the screen where you want it to be shown.

    Restore pop-ups snapped to the edge of the screen
    Drag an app in pop-up view t...

    • The security of your device has been improved.

    Model firmware by region