Samsung Galaxy XCover FieldPro G889AUCS7CUE1
SM-G889A 1 country Android 9

Samsung Galaxy XCover FieldPro G889AUCS7CUE1 Firmware

Samsung Galaxy XCover FieldPro G889AUCS7CUE1 is an Android 9 firmware for United States (ATT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G889AUCU6CUD4: bootloader binary raised from 6 to 7, so after installing it there is no way back to older builds. A newer build for SM-G889A is available: G889AUCS8CUL1.

Download firmware
9.1/10 (37)235 times
Android 9
OS Version
2021-05-24
Build Date
1
Countries
1
CSC codes
7
Bootloader binary

Bootloader binary 7. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy XCover FieldPro use bootloader binary 8 (latest: G889AUCS8CUL1). If your device already runs binary 8, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G889AUCS7CUE1
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G889A
    ATT United States
    		G889AATT7CUE1 3.237 GiB
    SM-G889A_1_20210524143138_zds90pckm0_fac.zip

    No matching downloads

    How to flash G889AUCS7CUE1

    • G889AUCS7CUE1 has bootloader binary 7. Your device must run binary 7 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    G889AUCS7CUE1 is Android 9 firmware for Samsung Galaxy XCover FieldPro, released for United States (ATT). Samsung built it on 2021-05-24.

    No. A newer build for SM-G889A is available: G889AUCS8CUL1. Install it instead of G889AUCS7CUE1 unless you need this exact version. The previous build was G889AUCU6CUD4.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 3.237 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy XCover FieldPro must be on bootloader binary 7 or lower.

    This build uses bootloader binary 7. It can be flashed on a Samsung Galaxy XCover FieldPro running binary 7 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 1 other build of this model uses the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy XCover FieldPro

    No changelog details available.
    Model firmware by region