Samsung Galaxy S6 Active (AT&T USA) G890AUCS7DRD3
SM-G890A 1 country

Samsung Galaxy S6 Active (AT&T USA) G890AUCS7DRD3 Firmware

Samsung Galaxy S6 Active (AT&T USA) G890AUCS7DRD3 is an Android firmware for United States (ATT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G890AUCU3BOJE: bootloader binary raised from 3 to 7, so after installing it there is no way back to older builds. A newer build for SM-G890A is available: G890AUCS7DRF2.

8.7/10 (27)142 times
n/a
OS Version
2018-05-18
Build Date
n/a
Security patch
1
Countries
1
CSC codes
7
Bootloader binary

Bootloader binary 7. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G890AUCS7DRD3
    ModelRegionCSC VersionSizeFile nameDownload
    SM-G890A
    ATT United States
    		G890AATT7DRD3 2.28 GiB
    SM-G890A_1_20180518153040_s8m28rnim7_fac.zip

    No matching downloads

    How to flash G890AUCS7DRD3

    • G890AUCS7DRD3 has bootloader binary 7. Your device must run binary 7 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 5.0
    • Display diagonal12.9 cm (5.1")
    • Display resolution2560 x 1440 pixels
    • Display typeSAMOLED
    • Processor frequency2.1 GHz
    • Processor familySamsung Exynos
    • Processor model7 Octa 7420
    • RAM4 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • SIM cardsSingle SIM
    • Battery capacity3500 mAh
    • Weight170 g

    Frequently Asked Questions

    No. A newer build for SM-G890A is available: G890AUCS7DRF2. Install it instead of G890AUCS7DRD3 unless you need this exact version. The previous build was G890AUCU3BOJE.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.28 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S6 Active (AT&T USA) must be on bootloader binary 7 or lower.

    This build uses bootloader binary 7. It can be flashed on a Samsung Galaxy S6 Active (AT&T USA) running binary 7 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S6 Active (AT&T USA)

    No changelog details available.
    Model firmware by region