SM-G890A 1 country

Samsung Galaxy S6 Active (AT&T USA) G890AUCS7DRF2 Firmware

Name: Samsung Galaxy S6 Active (AT&T USA) (SM-G890A)
Brand: Samsung
Availability: InStock

Samsung Galaxy S6 Active (AT&T USA) G890AUCS7DRF2 is an Android firmware for United States (ATT). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G890AUCS7DRE1 https://samfirm.shop/build/G890AUCS7DRE1, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. This is the newest build for SM-G890A.

8.9/10 (25)220 times

n/a

OS Version

2018-07-16

Build Date

n/a

Security patch

Countries

CSC codes

Bootloader binary

Bootloader binary 7. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Will it work on my device?

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.

MODEM/CP Version: G890AUCS7DRF2

Model	Region	CSC Version	Size	File name	Download
SM-G890A	ATT United States	G890AATT7DRF2	2.28 GiB	SM-G890A_1_20180716114040_9sudf9vrfp_fac.zip

Device specifications

Launched withAndroid 5.0
Display diagonal12.9 cm (5.1")
Display resolution2560 x 1440 pixels
Display typeSAMOLED
Processor frequency2.1 GHz
Processor familySamsung Exynos
Processor model7 Octa 7420
RAM4 GB
Rear camera resolution16 MP
Rear camera typeSingle camera
SIM cardsSingle SIM
Battery capacity3500 mAh
Weight170 g

How to flash G890AUCS7DRF2

Install Samsung USB Drivers:Download Official Drivers
Download Odin Flash Tool:

G890AUCS7DRF2 has bootloader binary 7. Your device must run binary 7 or lower: it is the 5th character from the end of your current build number.
CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
The Download Mode key combo depends on the model: see all combos.

Full flashing guide

Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

Frequently Asked Questions

Yes. G890AUCS7DRF2 is the newest build for SM-G890A on SamFirm. The previous build was G890AUCS7DRE1.

Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 2.28 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S6 Active (AT&T USA) must be on bootloader binary 7 or lower.

This build uses bootloader binary 7. It can be flashed on a Samsung Galaxy S6 Active (AT&T USA) running binary 7 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 2 other builds of this model use the same binary, so you can switch between them in both directions.