Samsung Galaxy S8 Active G892USQS5BSD4
SM-G892U 1 country Android 8.0.0 (Pie)

Samsung Galaxy S8 Active G892USQS5BSD4 Firmware

Samsung Galaxy S8 Active G892USQS5BSD4 is an Android 8.0.0 (Pie) firmware for United States (TMB). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G892USQS4BSC3: Android updated from Android 8.0.0 (Oreo) to Android 8.0.0 (Pie); bootloader binary raised from 4 to 5, so after installing it there is no way back to older builds. A newer build for SM-G892U is available: G892USQU7CUD2.

Download firmware
8.8/10 (458)4,464 times
Android 8.0.0 (Pie)
OS Version
2019-04-08
Build Date
1
Countries
1
CSC codes
5
Bootloader binary

Bootloader binary 5. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

Newer builds of Samsung Galaxy S8 Active use bootloader binary 7 (latest: G892USQU7CUD2). If your device already runs binary 7, this build cannot be flashed.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    MODEM/CP Version: G892USQS5BSD4
    ModelRegionCSC VersionRelease dateSizeFile nameDownload
    SM-G892U
    TMB United States
    		G892UOYN5BSD4 2019-05-07 3.769 GiB
    SM-G892U_1_20210426203806_b0bkybh96m_fac.zip

    No matching downloads

    How to flash G892USQS5BSD4

    • G892USQS5BSD4 has bootloader binary 5. Your device must run binary 5 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Frequently Asked Questions

    G892USQS5BSD4 is Android 8.0.0 (Pie) firmware for Samsung Galaxy S8 Active, released for United States (TMB). Samsung built it on 2019-04-08.

    No. A newer build for SM-G892U is available: G892USQU7CUD2. Install it instead of G892USQS5BSD4 unless you need this exact version. The previous build was G892USQS4BSC3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 3.769 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S8 Active must be on bootloader binary 5 or lower.

    This build uses bootloader binary 5. It can be flashed on a Samsung Galaxy S8 Active running binary 5 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 13 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S8 Active

    No changelog details available.
    Model firmware by region