Samsung Galaxy S5 G9008WZMU1BPD2
SM-G9008W 1 country Android 5.0 (Lollipop)

Samsung Galaxy S5 G9008WZMU1BPD2 Firmware

Samsung Galaxy S5 G9008WZMU1BPD2 is an Android 5.0 (Lollipop) firmware for China (CHM). It is the same firmware configured per region and carrier (CSC). Find your country below, verify the file and download for free. Compared with the previous build G9008WZMU1BOK3, Android and the bootloader binary are unchanged, so you can switch between the two in both directions. A newer build for SM-G9008W is available: G9008WZMS1CRH1.

Download firmware
9.0/10 (39)4,674 times
Android 5.0 (Lollipop)
OS Version
2016-04-15
First release
other regions until 2020-12-24
1
Countries
1
CSC codes
1
Bootloader binary

Bootloader binary 1. Flashing firmware with a lower binary is usually blocked by Samsung anti-rollback.

All regional downloads

Pick your region (CSC) to download the matching firmware package.

Paste your current build number from Settings > About phone (About tablet) > Software information, or the output of *#1234#.
    ModelRegionCSC VersionMODEM/CP VersionBuild DateRelease dateSizeFile nameDownload
    SM-G9008W
    CHM China
    		G9008WCHM1BPD2G9008WZMU1BTK1 2020-12-24 2020-12-28 1.35 GiB
    SM-G9008W_1_20201224155605_o5wf7hf2ft_fac.zip
    		Download
    SM-G9008W
    CHM China
    		G9008W1BPD2G9008WZMU1BPD2 2016-04-15 — — — Download

    No matching downloads

    How to flash G9008WZMU1BPD2

    • G9008WZMU1BPD2 has bootloader binary 1. Your device must run binary 1 or lower: it is the 5th character from the end of your current build number.
    • CSC: Use CSC for a clean install, to change the region (CSC code), to downgrade or to repair a device that does not boot.
    • HOME_CSC: Use HOME_CSC to update the same model and region while keeping your data. Back up anyway: a failed update can still require a reset.
    • The Download Mode key combo depends on the model: see all combos.
    Full flashing guide
    Beware: Manually flashing firmwares may brick your device. Use it at your own risk and follow our tutorial steps.

    Device specifications

    • Launched withAndroid 4.4.2
    • Display diagonal12.9 cm (5.1")
    • Display resolution1920 x 1080 pixels
    • Display typeSAMOLED
    • RAM2 GB
    • Rear camera resolution16 MP
    • Rear camera typeSingle camera
    • Battery capacity2800 mAh
    • Weight145 g

    Specifications of SM-G900, a regional variant of the same device. Chipset and SIM lines are left out: they can differ by region.

    Frequently Asked Questions

    G9008WZMU1BPD2 is Android 5.0 (Lollipop) firmware for Samsung Galaxy S5, released for China (CHM). Samsung built it on 2016-04-15.

    No. A newer build for SM-G9008W is available: G9008WZMS1CRH1. Install it instead of G9008WZMU1BPD2 unless you need this exact version. The previous build was G9008WZMU1BOK3.

    Download the package for your region (CSC) and unzip it. In Odin, load each file into the slot with the same name: BL, AP, CP (if the package has one) and CSC, or HOME_CSC to keep your data. Odin checks the built-in checksum of every .tar.md5 file before flashing. The download is 1.35 GiB; keep about twice that free on the computer to unzip it. The Samsung Galaxy S5 must be on bootloader binary 1 or lower.

    This build uses bootloader binary 1. It can be flashed on a Samsung Galaxy S5 running binary 1 or lower; if the device already has a higher binary, Odin stops with "SW REV CHECK FAIL". 15 other builds of this model use the same binary, so you can switch between them in both directions.

    Other builds and changelog for Samsung Galaxy S5

    No changelog details available.
    Model firmware by region